British Blend 100ml E-Liquid - Adding your own Nicotine

Here's a guide to how you can add Nicotine to your British Blend 100ml Nicotine Free E-Liquid:

ADDING NICOTINE TO CREATE 3MG E-LIQUID

What will I need?

    · 1 x bottle of British Blend 100ml E-Liquid (£10)

    · 1 x 10ml syringe (£0.40)

    · 1 x empty bottle (preferably 100ml£1.00)

    · 2 x Nicotine shot (£3.98)

    · Protective Goggles (Not sold by us)

    · Protective Gloves (Not sold by us)

    · Tissues (in case of spillage or leakage – Not sold by us)

How do I mix it?

    1. Put on your protective gloves and goggles.

    2. Open your full 100ml bottle of British Blend E-Liquid and use your 10ml syringe to transfer 17ml of it into your empty 100ml bottle. Close the spare bottle containing 17ml of liquid and put away for future use.

    3. Rinse out syringe with water.

    4. Use your syringe to add 17ml of Nicotine from the Nicotine Shots to your British Blend E-Liquid. With two Nicotine Shots you have 20ml of Nicotine, so you can add one full 10ml Nicotine shot without your syringe (if you feel comfortable doing so), then measure out the remaining 7ml with your syringe. Please note that VG Nicotine is very thick, so it can be difficult to pull it up into the syringe. Here’s a little tip to make the process easier: take the needle and lever/back piece off your syringe, hold it vertical so the thinner hole is facing downwards (you should be able to read the numbers correctly), then place your glove-protected finger or a tightly packed tissue over the smaller hole at the bottom. Pour 7ml of the second Nicotine shot into the larger hole at the top of the syringe, then once you are happy you’ve got 7ml, place the smaller hole over the top of your British Blend E-Liquid ready to add the Nicotine. Re-attach the lever/back piece to the syringe and add the 7ml of Nicotine to your British Blend E-Liquid. Wash the syringe with hot water three or four times ready for future use.

    5. Fasten lid on your British Blend E-Liquid and give it a good shake. This should then be ready to vape!

    6. After five mixes of the same flavour, if you remove 17ml of British Blend E-Liquid at the start of every mix and add them all to the same spare bottle, you will have enough left-over E-Liquid (85ml) to top it up with Nicotine (using the same process described above) and make a full 100ml bottle of 3mg British Blend E-Liquid.




    ADDING NICOTINE TO CREATE 6MG E-LIQUID

    What will I need?

      · 1 x bottle of British Blend 100ml E-Liquid (£10)

      · 1 x 10ml syringe (£0.40)

      · 1 x empty bottle (preferably 100ml£1.00)

      · 4 x Nicotine shot (£7.96)

      · Protective Goggles (Not sold by us)

      · Protective Gloves (Not sold by us)

      · Tissues (in case of spillage or leakage – Not sold by us)

    How do I mix it?

      1. Put on your protective gloves and goggles.

      2. Open your full 100ml bottle of British Blend E-Liquid and use your 10ml syringe to transfer 33ml of it into your empty 100ml bottle. Close the spare bottle containing 33ml of liquid and put away for future use.

      3. Rinse out syringe with water.

      4. Use your syringe to add 33ml of Nicotine from the Nicotine Shots to your British Blend E-Liquid. With four Nicotine Shots you have 40ml of Nicotine, so you can add three full 10ml Nicotine shots without your syringe (if you feel comfortable doing so), then measure out the remaining 3ml with your syringe. Please note that VG Nicotine is very thick, so it can be difficult to pull it up into the syringe. Here’s a little tip to make the process easier: take the needle and lever/back piece off your syringe, hold it vertical so the thinner hole is facing downwards (you should be able to read the numbers correctly), then place your glove-protected finger or a tightly packed tissue over the smaller hole at the bottom. Pour 3ml of the fourth Nicotine shot into the larger hole at the top of the syringe, then once you are happy you’ve got 3ml, place the smaller hole over the top of your British Blend E-Liquid ready to add the Nicotine. Re-attach the lever/back piece to the syringe and add the 3ml of Nicotine to your British Blend E-Liquid. Wash the syringe with hot water three or four times ready for future use.

      5. Fasten lid on your British Blend E-Liquid and give it a good shake. This should then be ready to vape!

    6. After two mixes of the same flavour, if you remove 33ml of British Blend E-Liquid at the start of each mix and add them both to the same spare bottle, you will have enough left-over E-Liquid (66ml) to top it up with Nicotine (using the same process described above) and make a full 100ml bottle of 6mg British Blend E-Liquid.

    Ratio breakdown:

    A table to show the different E-Liquid ratios you can achieve when adding your own Nicotine to British Blend 100ml Nicotine Free E-Liquid.

    Starting E-Liquid Ratio: 70VG / 30PG

    Starting E-Liquid Ratio: 60VG / 40PG

    Add 17ml Nicotine (3mg)

    Using VG Nicotine = 78.5VG / 21.5PG

    Using PG Nicotine = 61.5VG / 38.5PG

    Using VG Nicotine = 68.5VG / 31.5PG

    Using PG Nicotine = 51.5VG / 48.5PG

    Add 33ml Nicotine (6mg)

    Using VG Nicotine = 86.5VG / 13.5PG

    Using PG Nicotine = 53.5VG / 46.5PG

    Using VGNicotine = 76.5VG / 23.5PG

    Using PG Nicotine = 43.5VG / 56.5PG